Short answer
Use your meter’s diode mode. First find the base, which is the one pin that gives a forward reading against both of the other pins. For an NPN transistor, put the red probe on the base and the black probe on each other pin. You should see a forward reading, often roughly 0.5 to 0.7 V for silicon parts. For a PNP, swap the probes: black on the base, red on the other pins.
Before you start
- Take the transistor out of the circuit, or at least switch the circuit off and let any capacitors discharge. Other parts connected in parallel can change the readings.
- Find the part number and look up the pinout in the datasheet. Pin order differs between packages, so do not assume that the pins are in the order you expect.
- Set the meter to diode mode. Put the red lead in the V/Ω/diode jack and the black lead in COM. On a digital meter, the red lead is the positive terminal in this mode.
Step 1: Find the base
A bipolar transistor has two PN junctions, and they share the base pin. Test each pin against the other two in diode mode. The base is the pin that gives a forward reading to both of the other pins, with the same polarity. In many small packages the base is the middle pin, but that is not a rule. The datasheet is the reliable check.
Step 2: Identify NPN or PNP
- NPN: with the red probe on the base, you get forward readings to the collector and to the emitter. Reversing the probes gives an open reading (OL).
- PNP: with the black probe on the base, you get forward readings to the collector and to the emitter. Reversing the probes gives OL.
The polarity that gives the forward reading tells you the type.
Step 3: Check both junctions
Measure base to collector and base to emitter in both directions. A healthy junction shows a forward drop in one direction and OL in the other. A junction that shows OL both ways is likely open. A junction that reads close to zero both ways is likely shorted.
Step 4: Check collector to emitter
Probe between the collector and the emitter in both directions. A healthy transistor reads OL both ways. A reading near zero, or a continuity beep, means the device is shorted between those pins.
Telling the collector from the emitter
Diode mode cannot reliably tell the collector from the emitter, because both junctions look similar. There are two ways to check:
- The hFE socket: many multimeters have a transistor socket for measuring current gain (hFE). The socket is marked for NPN or PNP and shows its own pin order. Check that order against the datasheet before you trust the result.
- The datasheet: this is the most reliable way to confirm which pin is which.
Reading the results
| Measurement | Healthy transistor | Possible fault |
|---|---|---|
| Base to collector or emitter, forward polarity | Forward drop, often about 0.5 to 0.7 V | OL: open junction. Near zero: shorted junction |
| Base to collector or emitter, reverse polarity | OL | Any reading near zero suggests a leaky or shorted junction |
| Collector to emitter, both directions | OL | Near zero or a beep: shorted |
A Darlington transistor packs two transistors into one package. Its base-emitter forward drop is roughly double a single transistor’s, so a higher reading is expected. Check the datasheet before you judge the part.
Analog meters are different
Older analog multimeters often connect the internal battery with the opposite polarity in resistance mode. On those meters, the black lead is the positive terminal in ohms mode. Some older test instructions assume that arrangement, so they swap the probes compared with the steps above. Check your meter’s manual before you follow a probe-polarity step.
What a diode-mode test cannot tell you
A diode-mode test checks the junctions. It does not measure current gain, switching speed, or how much power the transistor can handle. A transistor that passes the junction test can still fail under load. For gain, use the hFE socket. For switching and power limits, check the datasheet.
For how BJTs and MOSFETs differ in use, see power transistor vs MOSFET. The junctions in a transistor behave like diodes, which are covered in types of diodes. Transistors are active components, as explained in active vs passive components.