The short answer
A capacitor discharges faster through a lower resistance. But a lower resistance also passes more current, so the resistor must handle more power at the start. For anything with real energy, use a suitably rated resistor rather than a bare short, and check the voltage with a meter before you touch the part.
For mains-connected and high-voltage parts, get a qualified technician to do the job.
Why the discharge speed depends on R × C
A capacitor discharging through a resistor follows an exponential curve. The time constant is τ = R × C. After about 5τ, the voltage has fallen to less than 1% of its starting value, which is close enough to zero for most purposes. See the RC time constant for the curve and the table.
Two things set the speed: the capacitance, which you cannot change, and the resistance, which you can. A smaller resistor gives a shorter τ and a faster discharge.
Why a bare short is not the answer
Shorting the terminals with a screwdriver or a piece of wire gives the fastest discharge, but it is also the most dangerous:
- The current surge can be large, causing sparks, a loud pop, and melted tips.
- The capacitor and its leads can be damaged.
- Metal tools can slip, and that can cause a short through the wrong path.
A bare short is only a low-concern option for very small, low-voltage capacitors. Even then, a resistor is the better habit.
Size the resistor for the power
The resistor must handle the power at the start of the discharge, when the voltage is highest:
This matters more than the speed. Compare two cases with the same 1 kΩ resistor:
- At 25 V, the starting power is 25² / 1,000 ≈ 0.6 W.
- At 300 V, the starting power is 300² / 1,000 = 90 W.
A small resistor rated for a fraction of a watt will overheat or fail at a few hundred volts. Choose a resistor with a power rating well above the starting power, use insulated leads, and keep your hands away from the resistor while it works.
A low-voltage example
For a small electronics capacitor, such as 470 µF at 25 V, a 1 kΩ resistor gives:
- τ = 1,000 × 0.000470 = 0.47 s
- about 5τ ≈ 2.4 s to near zero
At 25 V, the starting power is only about 0.6 W, so a resistor rated at 2 W or more gives a comfortable margin. Connect the resistor across the terminals with insulated leads, wait the full time, and then measure. See how to test a capacitor with a multimeter for the meter steps.
Use this as an example only. Check the voltage and energy of the part you are working on, and choose a resistor to match.
Check again: voltage can come back
Large capacitors, especially electrolytics, can recover some voltage after the discharge resistor is removed. This is called dielectric absorption or voltage rebound. Check the voltage again after a short wait, and discharge again if needed.
Never rely on the time alone. Measure the voltage with a meter set to DC volts, and check that it is near zero at the terminals before you touch them.
High-voltage and mains parts: stop and get help
Some parts can hold a dangerous charge even when the equipment is off or unplugged:
- Camera flash capacitors and other high-voltage units. See how a camera flash capacitor charges.
- AC motor run and start capacitors, which are connected to mains and store mains-level energy.
- Power supply bulk capacitors in mains equipment, such as TVs, monitors and microwaves.
Some equipment has a built-in bleeder resistor, but do not rely on it. If the part is high voltage or mains-connected and you are not trained to handle it, leave it to a qualified technician.
Key takeaways
- A lower resistance discharges a capacitor faster, but it passes more current and dissipates more power.
- Size the resistor for the starting power, P = V² / R, and use insulated leads.
- A bare short can spark, damage the part and cause injury. Avoid it.
- After about 5τ, the voltage is close to zero, but measure it rather than relying on time.
- Voltage can rebound after discharge, so check again.
- For high-voltage and mains-connected parts, call a qualified technician.