Capacitors

What is the typical lifespan of a capacitor?

How long capacitors last by type: electrolytic rated hours and the 10-degree rule, long-lived film and ceramic parts, and what shortens their life.

On this page
  1. The short answer
  2. Why there is no single number
  3. Electrolytic capacitors: rated hours and temperature
  4. Film capacitors
  5. Ceramic capacitors
  6. AC run capacitors (HVAC and motors)
  7. What shortens a capacitor’s life
  8. Signs of an aging capacitor
  9. Key takeaways

The short answer

There is no single lifespan for all capacitors. A typical electrolytic is rated for a number of hours at a stated temperature, often in the range of about 1,000 to 10,000 hours at 85°C or 105°C. Film and ceramic capacitors usually last much longer under normal conditions, and their life is limited more by overvoltage, heat and mechanical stress than by wear-out.

Always check the datasheet for the part you have, because the rated life depends on the specific product.

Why there is no single number

A capacitor’s life depends on:

  • Type: the dielectric and construction set the failure mechanism.
  • Temperature: heat is the biggest factor for most types.
  • Voltage and ripple: running near the rating, or with high ripple current, adds stress.
  • Environment: humidity, vibration and dust can all matter.

A part that runs cool, well below its rating, can outlast its datasheet figure by a wide margin. A part in a hot enclosure, near its voltage rating, may fail well before it.

Electrolytic capacitors: rated hours and temperature

Aluminum electrolytic capacitors have a liquid or gel electrolyte. Over time the electrolyte can slowly evaporate through the seal, and the capacitance falls while the equivalent series resistance (ESR) rises. This is called drying out, and it is the most common wear-out failure.

Datasheets state a life in hours at a maximum temperature, such as 2,000 hours at 105°C. Lower temperatures and lower ripple stress extend that figure.

The 10-degree rule of thumb

A common rule of thumb says that electrolytic life roughly halves for every 10°C rise above the rated temperature, and roughly doubles for every 10°C drop. This is an approximation, not a guarantee, but it explains why a part in a hot enclosure can wear out much sooner than its nominal rating suggests.

Stored electrolytic capacitors can also degrade, and very old equipment may need its capacitors reformed according to the service manual. This is a specialist task, so follow the documentation for the equipment.

Film capacitors

Film capacitors, such as polypropylene and polyester types, do not dry out in the same way. They are generally long-lived in normal use. Common failure causes are overvoltage, overheating and mechanical damage. Metalized film parts self-heal small faults, which slightly reduces capacitance over time but does not usually cause sudden failure.

For film parts, rely on the datasheet’s rated life and operating conditions. Many are specified for many years of normal use, but a figure is only meaningful at the stated voltage and temperature.

Ceramic capacitors

Ceramic capacitors have very long lives in normal use. Class II ceramics (such as X7R) lose some capacitance slowly with age, and the loss is faster after heating above the Curie point, which happens during soldering. Mechanical cracking from board flex or thermal shock is a more common cause of failure than wear-out.

AC run capacitors (HVAC and motors)

Run capacitors in air conditioners, fans and pumps are a special case. Their life depends on heat, voltage, how often the motor cycles, and power surges. Many run capacitors last many years, but no single figure is reliable, and online estimates vary widely. Treat any figure as a rough guide, not a warranty.

These parts store energy at mains voltage. If one needs replacing, follow the safety steps in how to discharge a capacitor faster, or use a qualified technician.

What shortens a capacitor’s life

  • Heat: the biggest factor for electrolytics.
  • Overvoltage: operating above the rating breaks down the dielectric.
  • High ripple current: heats the part from the inside.
  • Reverse polarity: damages polarized parts.
  • Power surges and spikes: stress the insulation.
  • Mechanical stress: can crack ceramics and break leads.

Signs of an aging capacitor

  • A bulged or domed top on an electrolytic
  • Leaked electrolyte or residue around the base
  • A reading well below the marked value on a capacitance meter
  • A device that restarts, hums, or runs hotter than normal

For what to look for in detail, see signs a capacitor is bad. Rising ESR is also a sign of an aging electrolytic, covered in ESR in capacitors.

Key takeaways

  • Electrolytics are rated in hours at a temperature, often about 1,000 to 10,000 hours at 85°C or 105°C.
  • Life roughly halves for every 10°C above the rating, as a rule of thumb.
  • Film and ceramic parts usually last much longer, with failures more often caused by overvoltage, heat or mechanical damage.
  • AC run capacitors have no reliable single lifespan. Heat, cycling and surges matter.
  • Check the datasheet for the rated life of the exact part.

The complete guide to capacitors

Capacitors Explained: How They Behave in DC and AC Circuits
Read the guide

Keep exploring

Guides from other topics

All topics →