Capacitors

RC Time Constant: Charging and Discharging a Capacitor

The RC time constant explained: how τ = R × C sets how fast a capacitor charges and discharges, with worked examples, a 63% and 37% table, and damping resistors.

On this page
  1. What the RC time constant means
  2. Charging and discharging curves
  3. Worked examples
  4. Measuring the time constant
  5. Damping, bleed and inrush resistors
  6. Rise time and cutoff frequency
  7. Key takeaways

What the RC time constant means

When a resistor and capacitor are connected in series, the capacitor does not charge or discharge instantly. The resistor limits the current, and the capacitor’s voltage changes gradually. The speed of that change is set by the time constant, written as the Greek letter τ (tau):

τ = R × C

Here R is the resistance in ohms and C is the capacitance in farads. Ohms multiplied by farads gives seconds, so τ is a time. A larger resistor or a larger capacitor gives a larger τ and a slower response.

Charging and discharging curves

When a capacitor charges from a DC source V0 through a resistor, the voltage across it follows:

v(t) = V0 × (1 − e^(−t/τ))

When it discharges from V0 through the resistor, the voltage falls as:

v(t) = V0 × e^(−t/τ)

Both curves are exponential. The change is fastest at the start and slows as the capacitor approaches its final voltage (or zero, when discharging). The table shows the percentages at each time constant:

Time Charged (percent of final voltage) Remaining during discharge
1 τ about 63.2% about 36.8%
2 τ about 86.5% about 13.5%
3 τ about 95.0% about 5.0%
4 τ about 98.2% about 1.8%
5 τ about 99.3% about 0.7%

After one time constant, the capacitor is about two-thirds of the way to its final voltage. After about five, it is close enough to the final value that most circuits treat the process as complete.

Worked examples

Example 1: R = 10 kΩ and C = 100 µF.

τ = 10,000 Ω × 0.0001 F = 1 second

The capacitor reaches about 63% of the supply voltage after 1 second and is close to fully charged after about 5 seconds.

Example 2: R = 1 kΩ and C = 10 µF.

τ = 1,000 Ω × 0.00001 F = 10 milliseconds

Keeping C the same but raising R to 10 kΩ gives τ = 100 milliseconds, ten times slower. This is the simplest way to see how the two components set the timing.

Measuring the time constant

On an oscilloscope, you can measure τ directly. Apply a step or square-wave signal to the RC network and watch the capacitor voltage. During charging, find the time to reach about 63.2% of the step. During discharging, find the time for the voltage to fall to about 36.8% of its starting value.

The measured value often differs a little from the calculated one. Component tolerances are a major cause. Electrolytic capacitors in particular can be ±20% or looser. Stray capacitance and the source’s output resistance also add to the total.

Damping, bleed and inrush resistors

A resistor placed with a capacitor usually does one of three jobs. The right value depends on which job it has.

  • Bleed resistor: Drains a capacitor slowly after power is removed. The time constant tells you roughly how quickly this happens, but for high-voltage or safety-critical parts, follow the design’s specified bleeder and see how to discharge a capacitor faster before handling anything.
  • Inrush limiting: A resistor in series limits the surge current when a discharged capacitor is connected to a voltage source. Without it, the surge can be large.
  • Damping: In a circuit with inductance, a capacitor and a resistor can damp ringing. A resistor in series with a capacitor, sometimes called a snubber, absorbs energy that would otherwise oscillate.

Choosing the value for any of these jobs depends on the circuit, so treat any general number as a starting point rather than a design.

Rise time and cutoff frequency

Two other useful results follow from τ = R × C:

  • Rise time (10% to 90%): For a first-order RC circuit, the rise time is about 2.2 × τ, or about 2.2 × R × C.
  • Cutoff frequency: For a simple RC low-pass filter, f_c = 1 / (2π × R × C). Below f_c, the signal passes mostly unchanged. Above it, the signal is attenuated.

For example, an RC network with τ = 1 ms has a rise time of about 2.2 ms between the 10% and 90% points.

Key takeaways

  • τ = R × C, in seconds when R is in ohms and C is in farads.
  • After 1 τ, a charging capacitor is at about 63% of its final voltage. During discharge, about 37% remains.
  • After about 5 τ, the change is close to complete for most purposes.
  • A larger R makes charging and discharging slower, not faster.
  • Bleed, inrush and damping resistors serve different jobs. Pick the value for the job, and do not rely on a time constant alone for safety.

The complete guide to capacitors

Capacitors Explained: How They Behave in DC and AC Circuits
Read the guide

Keep exploring

Guides from other topics

All topics →