Capacitors

Capacitor Polarity and Symbols: Finding the Positive and Negative Leads

Find the positive and negative leads on electrolytic and tantalum capacitors, read polarity symbols, avoid reverse-wiring damage, and spot three-lead parts.

On this page
  1. Why polarity matters
  2. Polarized and non-polarized capacitors
  3. Finding the positive and negative leads
  4. Reading capacitor symbols on schematics
  5. Three-lead capacitors
  6. What happens if you wire one backwards
  7. Check before you solder
  8. Key takeaways

Why polarity matters

Most capacitors do not care which way round they are connected. A few do. Polarized capacitors, mainly aluminum electrolytic and tantalum types, must have their positive lead at the higher voltage and their negative lead at the lower voltage. Connected the wrong way, they can overheat, leak, bulge or fail. Checking polarity before soldering is a cheap habit that prevents expensive mistakes.

Polarized and non-polarized capacitors

  • Polarized: aluminum electrolytic and tantalum capacitors. They have a positive and a negative terminal, and the schematic shows the polarity.
  • Non-polarized: ceramic disc, most film types (such as polypropylene and polyester) and mica. They can be connected either way round.

If a part is marked with a polarity sign, a stripe or a shaped lead, treat it as polarized. If you are unsure, look up the part’s datasheet.

Finding the positive and negative leads

Through-hole electrolytic

On a typical radial aluminum electrolytic, the negative lead is marked by a stripe along one side of the can, with minus signs printed on that stripe. The positive lead is on the unmarked side and is usually the longer of the two leads.

SMD electrolytic

On surface-mount aluminum electrolytic cans, a colored band or a marked corner usually indicates the negative terminal. Check the manufacturer’s drawing for the exact marking, because styles vary.

Tantalum

Tantalum capacitors reverse the convention on many parts. The positive end is often marked with a stripe, a notch or a plus sign, and the negative end is unmarked. Because the two marking styles are different, always read the marking on the part itself rather than assuming.

Film and ceramic

Film and ceramic capacitors are non-polarized, so there is no positive lead to find. Their markings show the value and tolerance, not polarity. See capacitor codes and markings for reading those values.

Reading capacitor symbols on schematics

The polypropylene (film) symbol

A polypropylene capacitor does not have its own schematic symbol. It uses the same symbol as every non-polarized capacitor: two straight, parallel lines. The dielectric type is named in the part’s label or in the bill of materials, such as “MKP” or “CBB” for metalized polypropylene. The symbol itself tells you only that the part is non-polarized.

The polarized symbol

A polarized capacitor is usually drawn with one straight plate and one curved plate. The curved plate is the negative side. Some schematics also add a plus sign next to the positive plate. If you see a symbol with a plus sign and a straight plate, that side is positive.

Three-lead capacitors

A three-lead capacitor has three terminals on one housing. The most common example is a dual-run capacitor used in air conditioners and other AC motor equipment. Such a part typically has a common (C) terminal, a HERM terminal and a FAN terminal, and it holds two capacitors in one case. The common terminal connects to both sections, and the other two connect to each section separately.

Some dual-section electrolytic and film parts also have three leads, so always check the markings or the datasheet.

Safety warning: AC motor capacitors store energy at mains voltage, even after the equipment is unplugged. Discharge a capacitor only with the method in how to discharge a capacitor faster, and leave air-conditioner and motor work to a qualified technician if you are not trained for it.

What happens if you wire one backwards

Reverse polarity is one of the most common ways to damage an electrolytic capacitor. Depending on the part and the voltage, a reverse-wired electrolytic may:

  • heat up and smell
  • leak electrolyte
  • bulge or vent
  • fail as a short circuit

Tantalum capacitors can fail as a short circuit, and in some cases the failure is dramatic. A reverse-wired polarized part should be replaced rather than reused. Do not power a circuit again until you have checked the part.

Check before you solder

  • Compare the part’s markings with the schematic.
  • Check the PCB silkscreen. Many boards show a plus sign or a stripe on the footprint.
  • If the schematic and the board disagree, check the datasheet and the design source before you solder.
  • If you are unsure, a quick continuity or diode-mode test can help identify some faults, but it does not reliably show polarity. Trust the markings and the datasheet.

Key takeaways

  • Electrolytic and tantalum capacitors are polarized, and film and ceramic parts are usually not.
  • Aluminum electrolytics mark the negative side, usually with a stripe. Tantalum chips often mark the positive side.
  • A polypropylene capacitor uses the same non-polarized symbol as other film parts. The dielectric is named in the label.
  • Three-lead parts are often dual-section, and AC motor capacitors need safe handling.
  • Check the markings, the schematic and the PCB before soldering.

The complete guide to capacitors

Capacitors Explained: How They Behave in DC and AC Circuits
Read the guide

Keep exploring

Guides from other topics

All topics →