Capacitors

How to Read Capacitor Codes and Markings (Ceramic, SMD and Electrolytic)

How to read capacitor codes and markings on ceramic, SMD and electrolytic parts, with examples like 106J and 104 and a tolerance letter table.

On this page
  1. Three-digit codes on ceramic and film parts
  2. Tolerance letters
  3. Values with letters and decimal points
  4. SMD capacitors: few markings
  5. Electrolytic capacitors: printed values
  6. Dielectric codes
  7. Quick reference
  8. Key takeaways

Three-digit codes on ceramic and film parts

Most ceramic disc and many film capacitors use a three-digit code. The rule has two parts:

  • The first two digits are significant figures.
  • The third digit is the multiplier, the number of zeros to add.

The result is in picofarads (pF). So 104 is 10 followed by four zeros, which is 100,000 pF, or 100 nF, or 0.1 µF.

Code Value in pF Value in µF
101 100 pF 0.0001 µF
102 1,000 pF (1 nF) 0.001 µF
103 10,000 pF (10 nF) 0.01 µF
104 100,000 pF (100 nF) 0.1 µF
105 1,000,000 pF (1 µF) 1 µF
224 220,000 pF (220 nF) 0.22 µF
106 10,000,000 pF (10 µF) 10 µF

Film capacitors use the same idea. A film part marked 223 is 22 nF, or 0.022 µF. This is the common tone-capacitor value in guitars, described in capacitors in audio.

What 107 means

Applying the rule to 107 gives 10 × 10⁷ pF, which is 100,000,000 pF, or 100 µF. A 100 µF value is unusual on a ceramic chip, so a 107 marking on a small ceramic part is worth a second look. Check the part type, the size and the datasheet before you trust the value. Electrolytic and other parts often print their values in a different style, so read the whole label, not only the code.

Tolerance letters

A letter after the code gives the tolerance:

Letter Tolerance
C ±0.25 pF (small values)
D ±0.5 pF (small values)
F ±1%
G ±2%
J ±5%
K ±10%
M ±20%
Z +80% / −20% (typical of Y5V ceramics)

So 106J is 10 µF ±5%, and 104K is 100 nF ±10%. The letter tells you how far the real value may differ from the printed one.

Values with letters and decimal points

Some parts print the value with a letter in place of the decimal point:

  • p for picofarads: 22p = 22 pF
  • n for nanofarads: 4n7 = 4.7 nF, and n47 = 0.47 nF
  • µ (or u) for microfarads: 0.1µ = 0.1 µF

Values below 10 pF may use R as the decimal point, so 2R2 means 2.2 pF.

SMD capacitors: few markings

Surface-mount ceramic capacitors are very small, so most are unmarked. If the part has no code, use the design documents or the manufacturer’s datasheet, or measure it after removal. See how to find the value of a ceramic capacitor.

Telling an SMD capacitor from an SMD resistor

SMD resistors and SMD capacitors can look alike, and the codes are a common source of confusion:

  • Resistors often have a dark (black, blue or green) top coating over a pale body, a flatter profile and squarer end terminals. Their codes are in ohms. A resistor marked 103 is 10 kΩ.
  • Ceramic capacitors (MLCCs) usually look solid tan, brown or off-white, with no painted top. They often look slightly taller and have rounded end caps that wrap around the sides. Their codes, if present, are in picofarads. A capacitor marked 103 is 10 nF.

The same three-digit code means different things on the two parts, so check which part you are looking at before you decode it.

Package sizes

SMD parts come in standard sizes, such as 0402, 0603, 0805 and 1206. These are imperial dimensions. For example, a 0603 part is about 1.6 × 0.8 mm. Size tells you about the package, not the value. Larger packages often handle more voltage or power, but the datasheet gives the real ratings.

Electrolytic capacitors: printed values

Aluminum electrolytic capacitors usually print the value directly, for example “100 µF”, along with the voltage rating and often a temperature rating such as 105°C. The negative lead is marked by a stripe with minus signs. See capacitor polarity for the full guide to leads and symbols.

Electrolytic capacitors rarely use the three-digit code, so read the printed value first.

Dielectric codes

Some ceramic capacitors also print a dielectric class, such as X7R, X5R, C0G (also called NP0) or Y5V. The class tells you how stable the capacitance is with temperature and voltage. Class II types such as X7R and X5R lose capacitance under DC bias, so a labeled 10 µF part may read lower when it is working at its rated voltage.

Quick reference

  • Three digits on a ceramic or film part: first two digits, then the number of zeros, in pF.
  • 104 = 100 nF, 103 = 10 nF, 102 = 1 nF, 223 = 22 nF, 106J = 10 µF ±5%.
  • 107 = 100 µF, unusual on chips, so check the part.
  • Resistor codes are in ohms. 103 on a resistor is 10 kΩ.
  • Electrolytics print the value, voltage and a negative stripe.
  • SMD ceramic capacitors are often unmarked.

Key takeaways

  • Read ceramic and film codes as two significant digits plus a multiplier, in pF.
  • A letter after the code gives the tolerance: J is ±5%, K is ±10% and M is ±20%.
  • SMD capacitors are often unmarked. Check the datasheet or measure the part.
  • The same code means ohms on a resistor and picofarads on a capacitor.
  • Electrolytics print the value directly, with a negative stripe on the negative lead.

The complete guide to capacitors

Capacitors Explained: How They Behave in DC and AC Circuits
Read the guide

Keep exploring

Guides from other topics

All topics →