What ESR is
ESR stands for equivalent series resistance. Every real capacitor behaves like an ideal capacitor with a small resistor in series with it. That resistor is the ESR. It is not a physical part you can remove. It is the sum of all the resistive losses inside the capacitor.
An ideal capacitor stores and returns energy with no loss. A real capacitor loses some energy as heat each time current flows through it, and the ESR is what causes that loss.
Where ESR comes from
ESR has several sources:
- Leads and terminals: the wires, welds and foil or electrode connections
- Electrodes: the resistance of the metal or conductive layers
- Dielectric losses: energy lost in the insulating material as it is repeatedly polarized
- Electrolyte resistance: in aluminum electrolytic capacitors, the liquid or gel electrolyte conducts ions, which adds resistance
The total depends on the capacitor type, its size and its construction. Ceramic capacitors (MLCCs) usually have very low ESR. Aluminum electrolytics usually have a much higher ESR, and it can be a major part of their behavior in a circuit.
Why ESR matters
Heating (I²R)
When current flows through the ESR, power is lost as heat: P = I² × R. A capacitor with a high ESR carrying a high ripple current heats up.
For example, a 470 µF electrolytic with 0.5 Ω ESR carrying 2 A of ripple current dissipates P = 2² × 0.5 = 2 W inside the capacitor. That heat shortens the part’s life, and it can start a cycle of drying out and rising ESR.
Ripple voltage
In a power supply, the ripple voltage across a filter capacitor includes a part that is just the ripple current multiplied by the ESR. A higher ESR gives a larger ripple voltage at the output, even if the capacitance is correct.
Transient response and efficiency
A capacitor with a high ESR responds more slowly to sudden load changes, because the resistance limits how quickly it can deliver current. That can cause voltage dips. The heat from ESR also wastes power, which reduces efficiency. In a switching power supply, this can matter a great deal.
ESR and aging in electrolytics
Aluminum electrolytic capacitors dry out over time, as the electrolyte slowly escapes or degrades. As they dry out, their capacitance falls and their ESR rises. The rising ESR causes more heating, which speeds up the drying out.
This is why ESR is often a better early warning than capacitance. A part can still read close to its marked capacitance on a basic meter while its ESR has risen enough to cause ripple or heating problems. For more on aging, see the typical lifespan of a capacitor.
ESR and temperature
ESR changes with temperature. In aluminum electrolytics, ESR generally rises as the temperature falls, which can affect cold starts. It also rises as the part ages. The exact change depends on the part, so check the datasheet’s ESR and temperature curves rather than relying on a general figure.
ESR, ESL and self-resonance
At high frequencies, a second parasitic element matters: equivalent series inductance (ESL), which comes from the leads and internal structure. ESL and capacitance form a resonance, called the self-resonant frequency:
f = 1 / (2π√(LC))
Below this frequency, the capacitor behaves as a capacitor. Above it, the part behaves as an inductor, so its impedance rises again. For example, a 10 nF capacitor with 0.5 nH of ESL resonates near 71 MHz. With 2 nH of ESL, the resonance falls to about 36 MHz. The lower the ESL, the higher the frequency at which the capacitor still works well.
This is why small ceramic capacitors are used for high-frequency bypassing: they have low ESL as well as low ESR.
Which capacitors have low ESR
- Multilayer ceramic (MLCC): very low ESR, and low ESL in small packages.
- Film capacitors: low ESR, especially polypropylene types.
- Polymer electrolytics: designed for low ESR compared with standard aluminum electrolytics.
- Standard aluminum electrolytics: higher ESR, and the value varies widely with size and design.
Low-ESR electrolytics are often sold for switching power supplies, and the datasheet gives the ESR at a given frequency.
How to measure ESR
- ESR meter: a dedicated meter applies a small test signal and reads the ESR directly. It is the simplest tool for electrolytics.
- LCR meter: measures impedance at a chosen frequency. The resistive part of the impedance is the ESR.
- Estimate from the datasheet: ESR ≈ DF × Xc, where DF is the dissipation factor from the datasheet and Xc is the capacitive reactance at the frequency of interest.
A basic multimeter does not measure ESR. A capacitance reading alone cannot show a high ESR. Discharge the capacitor before any measurement, and see how to test a capacitor with a multimeter for the limits of a basic meter.
Key takeaways
- ESR is the internal series resistance of a capacitor, and it causes heating and ripple.
- In electrolytics, ESR rises with age and at low temperature, and it is often the first sign of a failing part.
- ESR and ESL together set the self-resonant frequency, above which a capacitor acts as an inductor.
- A basic multimeter cannot measure ESR. Use an ESR or LCR meter for electrolytics in power circuits.