Circuit Theory

Electrical Power in a Circuit: Formulas, Units and RF Power Conversion

Power in a circuit explained with the core formulas, units (watts vs joules), AC power basics, and a guide to converting RF power into voltage.

On this page
  1. Power is the rate of energy transfer
  2. The core formulas
  3. Watts, joules and the common mix-up
  4. Power in AC circuits
  5. Converting RF power to voltage
  6. Quick reference

Power is the rate of energy transfer

Power is how fast energy moves from a source into a load, or is converted into another form. It is measured in watts (W). One watt is one joule per second, so energy equals power multiplied by time:

  • Energy (J) = power (W) × time (s)
  • Example: a 36 W load running for 10 seconds uses 36 × 10 = 360 J.

Utility bills use kilowatt-hours (kWh) for energy. One kWh is 1,000 W sustained for one hour, which equals 3.6 million joules (3.6 MJ).

The core formulas

For a resistive DC circuit, power follows from voltage and current:

  • P = V × I
  • Using Ohm’s law (V = I × R), the same power can be written as P = I² × R or P = V² / R.

Worked examples:

  • A 12 V source across a 4 Ω resistor. Current is I = 12 V / 4 Ω = 3 A. Power is P = 12 V × 3 A = 36 W. Check with P = V² / R: 12² / 4 = 144 / 4 = 36 W.
  • A 2 A current through a 5 Ω resistor. Power is P = 2² × 5 = 20 W.

Use whichever form matches the values you know. If you know only the current and resistance, use I²R. If you know only the voltage and resistance, use V²/R.

Watts, joules and the common mix-up

“Power is measured in joules” is a common search phrase, but it is wrong. Energy is measured in joules. Power is measured in watts, which are joules per second. A 60 W light bulb uses 60 J of energy every second. Over an hour, that is 216,000 J, or 0.06 kWh.

For a fuller definition of the joule, see What is a joule of energy?.

Power in AC circuits

In AC circuits, voltage and current change direction and may not peak at the same moment. The phase angle φ is the time offset between them, and the power factor is cos φ.

  • Real power (P), in watts: P = Vrms × Irms × cos φ. This is the power that does useful work.
  • Apparent power (S), in volt-amperes (VA): S = Vrms × Irms.
  • Reactive power (Q), in volt-amperes reactive (VAR): Q = Vrms × Irms × sin φ. Inductors and capacitors store this power and return it each cycle.
  • Power factor: cos φ = P / S.

For a purely resistive load, φ = 0, the power factor is 1, and P = S.

Example: a load draws 2 A rms at 120 V rms, with a phase angle of 60°. Real power is 120 × 2 × 0.5 = 120 W. Apparent power is 240 VA. The power factor is 0.5.

Converting RF power to voltage

RF (radio-frequency) power is often quoted in dBm, which is decibels relative to 1 mW. The conversion from power to voltage needs the load impedance, which is often 50 Ω in RF work. Without a resistance or impedance, you cannot convert watts to volts.

Step 1: dBm to watts. Power in milliwatts is P(mW) = 10^(dBm / 10). Divide by 1,000 to get watts.

  • 0 dBm = 1 mW = 0.001 W
  • 10 dBm = 10 mW = 0.01 W
  • 30 dBm = 1,000 mW = 1 W

Step 2: watts to RMS volts. For a resistive load, P = V_rms² / R, so V_rms = √(P × R).

At 50 Ω:

  • 1 W gives V_rms = √(1 × 50) ≈ 7.07 V. For a sine wave, the peak voltage is √2 × V_rms ≈ 10 V.
  • 0 dBm (1 mW) gives V_rms = √(0.001 × 50) ≈ 0.224 V.

The same power in a 75 Ω system gives a different voltage. At 1 W, V_rms = √75 ≈ 8.66 V. Always state the impedance.

Is an RF signal AC or DC? An RF signal is an alternating (AC) signal. Its power is usually quoted as an average, so the voltage in the formula is an RMS value.

Converting peak and RMS. For a sine wave, V_rms = V_peak / √2, and the peak-to-peak voltage is 2√2 × V_rms.

Quick reference

Quantity Formula Unit
Power (DC) P = V × I watts (W)
Power in a resistor P = I² × R or V² / R watts (W)
Energy E = P × t joules (J) or kWh
AC real power P = Vrms × Irms × cos φ watts (W)
Power factor cos φ = P / S none
RMS of a sine wave Vrms = Vpeak / √2 volts (V)
dBm to watts P(W) = 10^(dBm / 10) / 1,000 watts (W)

For the AC analysis behind these formulas, see RLC Circuits. For the general starting point, see Circuit Analysis Basics.

The complete guide to circuit theory

Circuit Analysis Basics: Voltage, Current and Sources
Read the guide

Keep exploring

Guides from other topics

All topics →