Electric Motors

Types of Electric Motors: DC, Servo and Stepper Compared

Compare DC, brushless, servo and stepper motors for hobby projects: how each works, how servo and stepper differ, and whether a DC motor is an actuator.

On this page
  1. The main motor types at a glance
  2. Brushed DC motors
  3. Brushless DC motors
  4. Servo motors
  5. Stepper motors
  6. Servo vs stepper: the key differences
  7. Is a DC motor an actuator?
  8. Transformer vs motor
  9. How to choose

Electric motors come in several families, and the names on a datasheet can be confusing. This guide covers the four types most hobby projects use: brushed DC, brushless DC, servo and stepper motors. It also answers two common questions: whether a DC motor counts as an actuator, and how a motor differs from a transformer.

The short version: a brushed DC motor spins when you apply voltage, and its speed depends mostly on that voltage. A servo is a motor with position feedback and a control circuit, so it can move to a set angle. A stepper moves in fixed steps and usually has no feedback. A brushless DC motor uses electronics instead of brushes, so it needs a controller.

The main motor types at a glance

Type How it is controlled Built-in position feedback Typical hobby use
Brushed DC Voltage, often with PWM No Toys, fans, small drives
Brushless DC Electronic speed controller (ESC) No. Hall sensors, if fitted, only report rotor position for switching Drones, RC cars, power tools
Servo PWM pulse that sets an angle Yes Robot joints, steering, pan-tilt mounts
Stepper Pulses from a driver, one per step No (open loop) 3D printers, small CNC machines, linear stages

Brushed DC motors

A brushed DC motor has a set of magnets (or field coils) and a rotor with windings. Brushes press against a commutator, a split ring on the rotor. As the rotor turns, the commutator reverses the current in the windings so the rotor keeps turning in the same direction.

Brushed motors are simple and inexpensive, and you can run one from a battery and a switch. The brushes and commutator wear over time, and they create sparks and electrical noise. Reversing the supply leads reverses the direction. For speed control, most people use PWM, explained in DC motor speed control using PWM. For a controller that reverses the motor electronically, see how to reverse a DC motor with an H-bridge.

Brushless DC motors

A brushless DC (BLDC) motor puts the permanent magnets on the rotor and the windings on the stator. With no brushes, something outside the motor has to switch the current in each winding. That job belongs to an electronic speed controller (ESC) or a driver. Most BLDC motors have three wires, one per phase.

The controller needs to know where the rotor is. It can read Hall sensors, or it can infer the position from the voltage the spinning magnets induce in the windings (sensorless control). Sensorless control needs the motor to be turning before it can read that voltage, so it struggles at standstill and very low speed.

Brushless motors have no brush wear and are common in drones and RC vehicles. They are often more efficient and can run faster than brushed motors of similar size. The cost is the extra electronics. For details, see brushless DC motors explained, and for wiring, how to connect a brushless motor to an ESC.

Servo motors

A servo is a complete position-control system. It contains a motor, a gearbox, a position sensor (usually a potentiometer or encoder) and a control circuit. You send a target position, and the circuit drives the motor until the sensor reading matches it.

A hobby servo expects a control pulse about 50 times per second. The width of each pulse sets the angle, commonly between 1 ms and 2 ms for roughly 0 to 180 degrees. Many hobby servos turn about 180 degrees, though models vary. For more on range, see how much a servo motor can turn.

Servos suit robot joints, steering linkages and any job that needs a set angle. Because the control loop keeps correcting toward its target, a servo holds its angle against a load up to its torque rating.

Stepper motors

A stepper motor has coils arranged so that energising them in sequence turns the rotor in fixed steps. A common stepper moves 1.8 degrees per full step, which is 200 steps per revolution. A driver chip sends current to each coil. Each pulse you send moves the motor one step, or one fraction of a step if the driver microsteps.

In a basic setup, a stepper has no feedback, so it relies on the controller counting steps accurately. It works well when the load stays within the motor’s torque. If the load is too heavy, the motor can skip steps without telling the controller. For wiring, see stepper motor wiring. For a driver setup, see driving a stepper with an Arduino and an A4988.

Servo vs stepper: the key differences

Servo and stepper motors are the two types people compare most often.

Point Servo Stepper
Position feedback Yes (closed loop) Usually none (open loop)
Rotation Standard hobby servos about 180 degrees; continuous-rotation versions also exist Continuous, in fixed steps
Speed and torque Holds torque better as speed rises Torque tends to fall as speed rises
Cost and complexity Higher Lower
Lost steps Corrected by feedback Possible if overloaded

In short, a stepper suits repeatable positioning at low to moderate speed, where loads are predictable and cost matters. A servo suits jobs that need feedback, faster motion or a load that changes.

Is a DC motor an actuator?

It depends on the definition. In the broad sense, an actuator is any device that turns a control signal into physical motion. A DC motor does that, so many people call it an actuator.

In engineering, “actuator” often means a complete unit ready to move a load. A linear actuator, for example, is a motor combined with a gearbox and a screw or similar mechanism that pushes and pulls. A bare DC motor usually needs a gearbox, a driver or a mechanism before it can do a useful job.

Transformer vs motor

A transformer and a motor both use magnetism, but they do different jobs. A transformer changes the voltage of an AC supply by linking two coils through a shared core. It has no moving parts. A motor converts electrical energy into rotation. Some AC motors use induction to turn their rotor, but a transformer is a static device. For how induction works in a transformer, see does a transformer use induction.

How to choose

  • Simple spinning from a battery: brushed DC motor.
  • High speed and efficiency for a drone or RC vehicle: brushless DC motor with an ESC.
  • A set angle with minimal wiring: hobby servo.
  • Repeatable steps, open-loop control: stepper motor with a driver.

Check the datasheet for voltage, current and torque before you buy. Match those numbers to your supply and load.

Keep exploring

Guides from other topics

All topics →