A brushless DC (BLDC) motor is a permanent-magnet motor that switches its own current electronically instead of using brushes. Because the controller has to energise each winding in the right order, a BLDC motor is almost always run with a driver, usually an electronic speed controller (ESC). This article explains how the parts fit together, how the controller knows where the rotor is, and why sensorless control is harder at low speed.
Brushless vs brushed: the basic difference
In a brushed motor, brushes and a commutator switch the current. In a BLDC motor, electronics do that switching. With no brushes, there is no brush wear, no brush dust and much less electrical noise from sparking. Many BLDC motors are also more efficient than brushed motors of similar size. Those are general trends. Efficiency depends on the design, the load and the controller.
The trade-off is cost and complexity. A brushed motor runs from a plain DC supply. A BLDC motor needs a controller that knows the rotor position and switches the phases in sequence.
How a BLDC motor is built
- Rotor: permanent magnets, usually with several pole pairs.
- Stator: a laminated iron core with copper windings sitting in slots.
- Phases: the windings form three groups, usually labelled A, B and C. Each phase has its own wire, so a typical BLDC motor has three power wires.
Motors built as outrunners have the magnets on an outer rotor that spins around a fixed stator. Many drone motors are built this way. Inrunners have the rotor inside the stator. The electrical principle is the same.
Windings and the coil layout
The three phase windings are usually joined at one point, a star (or wye) connection. The other end of each winding goes to the controller.
ESC phase A ──[ winding A ]──┐
ESC phase B ──[ winding B ]──┼── common (star) point
ESC phase C ──[ winding C ]──┘
Some motors use a delta connection instead. The outside wiring still uses three wires. The controller drives the windings in a sequence, so the stator’s magnetic field keeps pulling the rotor magnets around.
Commutation: switching the coils in sequence
In the common six-step method, the controller energises two of the three phases at a time: one as the supply side and one as the return. The third phase is left floating. Each of the six combinations pushes the rotor through one 60-degree electrical step, and then the cycle repeats.
Sinusoidal and field-oriented control drive the phases with smoother waveforms. They reduce torque ripple and noise, but they need more processing. You will mostly see them in higher-end ESCs and industrial drives.
Hall sensors: knowing the rotor position
Hall sensors are small magnetic switches, usually three of them, placed around the stator. Each one changes state as a rotor magnet passes. Together, the three signals identify which of the six commutation steps the rotor is in. The controller can then switch each step at the right moment, including when the motor starts from a standstill.
A sensored motor has a separate sensor cable, often five wires: sensor power, ground and three sensor signals. Use the sensor cable that the ESC and motor are designed for. A wrong connection can make the motor run badly.
Sensorless control: reading the back-EMF
Without Hall sensors, the controller reads the voltage induced in the floating phase. As the rotor turns, its magnets induce a voltage in the windings, called back-EMF. The controller watches for the point where that voltage crosses the midpoint of the phases, and uses that moment to time the next step.
Back-EMF is proportional to speed. At standstill or very low speed, it is too small to read reliably. Most sensorless controllers therefore start the motor with a forced or ramped sequence, then switch to back-EMF sensing once the motor is turning. That is why sensorless motors can stall, hesitate or start roughly at low throttle.
Sensorless designs are common in fans, drones and other applications where the motor runs at useful speed most of the time. Robot joints and positioning systems usually prefer sensored control, because they need smooth low-speed motion and a reliable start from rest.
Practical checks before you power up
- Use an ESC rated for the motor’s voltage and current. For high-KV motors, check the ESC’s maximum RPM limit as well.
- Connect the three motor wires before you connect the battery.
- If the motor runs backwards, swap any two of the three motor wires with the power off.
- Sensored motors need the right sensor cable and phase order. Sensorless motors do not.
For the speed relationship, see brushless motor KV vs turns. For the wiring steps, see how to connect a brushless motor to an ESC. For the bigger picture, see types of electric motors.