Electric Motors

How to Build a Homemade Electric Motor With a Battery, Magnet and Copper Wire

Build a simple homopolar motor from a battery, a neodymium magnet, a steel screw and copper wire, and learn the Lorentz force behind the spin.

On this page
  1. What you need
  2. Safety first
  3. Version 1: the screw and magnet
  4. Version 2: the wire loop
  5. Why it spins, and how to reverse it
  6. Bonus: a simple electromagnet
  7. What this shows, and what it does not

You can make a simple spinning motor from one battery, a strong magnet and some copper wire. The design is a homopolar motor. Current flows through the magnet, and the magnet’s field pushes sideways on that current, so the assembly turns. It takes a few minutes and is a classic demonstration of the Lorentz force. It is not a practical motor, but it shows the basic principle.

What you need

  • One alkaline battery, such as an AA.
  • One neodymium disc magnet, for example 15 mm across and 8 mm thick, N-grade.
  • One steel or iron screw with a straight, flat tip.
  • A short length of stiff copper wire, about 1 mm thick. For the wire-loop version, use about 30 cm.
  • Pliers or wire strippers to bare the ends of the wire.

Safety first

  • Neodymium magnets are very strong. They can pinch fingers hard, and they can chip or shatter if they snap together. Keep them apart while you handle them.
  • Keep magnets away from children, and never let anyone swallow one. Swallowed magnets can cause serious internal injury.
  • Keep strong magnets away from pacemakers and similar medical devices.
  • A short-circuited battery and wire get hot quickly. Connect the circuit only for a few seconds at a time, and disconnect as soon as the magnet starts to spin.
  • Use a single alkaline cell. Do not use lithium or rechargeable cells for this project, because a short circuit can make them overheat.

Version 1: the screw and magnet

  1. Stick the magnet to the head of the screw.
  2. Place the tip of the screw on the negative (flat) end of the battery. The screw should be able to turn on that contact, and the magnet should be free to rotate.
  3. Hold one bared end of the copper wire against the positive end of the battery, using your finger to press it on.
  4. Let the other bared end of the wire touch the outer edge of the magnet.
  5. The magnet and screw should start to turn. Disconnect once you have seen it spin.

If nothing happens, check the contacts. The screw tip must press firmly on the battery’s negative end, and the wire must touch both the battery’s positive end and the magnet. If the screw wobbles, its tip may be bent. File the tip flat or use a straighter screw. Larger magnets are usually easier to get spinning.

Version 2: the wire loop

A wire-loop version is also possible. The wire forms a loop that rests on a magnet and makes contact at the battery. It is harder to balance and to keep in good contact, so start with the screw version. Once that works, you can try the loop and compare.

Why it spins, and how to reverse it

The circuit runs from the battery’s positive end, through the wire and the magnet, through the screw, and back to the battery’s negative end. The magnet’s field is at right angles to the current flowing through it. That produces a sideways force, the Lorentz force, which turns the magnet and screw around the battery’s contact.

The spin direction depends on two things: the direction of the current and the orientation of the magnet’s poles. Reversing the battery reverses the current. Flipping the magnet reverses the field. Reversing either one reverses the spin. Reversing both does not.

Bonus: a simple electromagnet

If you wrap insulated copper wire around an iron nail and connect the two ends of the wire to a battery, the nail becomes a magnet while current flows. It can pick up small steel items, such as paper clips. Disconnect the battery to switch it off. A nail is not as strong as a permanent magnet, and the same short-circuit caution applies: do not leave the battery connected for long.

What this shows, and what it does not

This project shows the Lorentz force in action, which is the same principle behind many motors. It does not produce useful torque, and it does not control speed. Real motors use coils, switched in sequence, to keep the rotor turning. For the main motor types, see types of electric motors, and for a switched design, see brushless DC motors.

The complete guide to electric motors

Types of Electric Motors: DC, Servo and Stepper Compared
Read the guide

Keep exploring

Guides from other topics

All topics →