KV and turns are the two numbers most often quoted for brushless motors. Neither one measures power on its own. KV tells you how fast the motor spins per volt with no load. Turns describe how the stator is wound, which sets KV and torque together. This article explains both and shows how to use them when you choose a motor.
What KV means
KV is the no-load speed in RPM per volt applied. A 1000KV motor turns at about 1000 RPM for each volt, with no load and no propeller. On 11.1 V, which is the nominal voltage of a 3-cell LiPo pack, a 1000KV motor would reach roughly 11,100 RPM in theory. With a load, the real speed is lower.
KV is not power. Power is voltage multiplied by current, and the current depends on the load. A high-KV motor on a low voltage can produce less power than a low-KV motor on a higher voltage.
Estimating speed from KV and voltage
Use this as a rough upper limit:
No-load RPM ≈ KV × battery voltage
Battery voltage changes with charge state and load. A LiPo cell is about 3.7 V nominal and about 4.2 V when fully charged. So a 3S pack is about 11.1 V nominal and about 12.6 V fully charged, and a 4S pack is about 14.8 V nominal.
A propeller slows the motor. The heavier the load, the further the actual speed falls below the no-load figure. Treat the formula as a starting point, not a prediction.
What turns mean
A turn is one wrap of wire through a stator tooth or coil. Makers count turns in different ways, so compare turn counts only within the same motor family and from the same maker.
Winding the same stator with more turns, or fewer, changes how the motor behaves. Assuming the same wire gauge:
| Change | KV | Torque per amp | Speed at a given voltage | Winding resistance |
|---|---|---|---|---|
| More turns | Lower | Higher | Lower | Higher |
| Fewer turns | Higher | Lower | Higher | Lower |
KV vs turns: the trade-off
A low-KV motor with more turns gives more torque per amp. It suits large propellers, heavy loads and slow, high-torque jobs. A high-KV motor with fewer turns spins faster and suits small propellers and light loads. For the same torque, it draws more current.
Turn counts also appear in racing rules. Many RC car classes set a turn count so that motors can be compared fairly. In a spec-class race, the turn count matters more than the KV printed on the box.
Motor size matters too
KV and turns do not describe the motor’s size or mass. Two motors with the same KV can differ a lot in torque if one is larger or heavier. RC hobbyists often report that a heavier outrunner at a lower KV can outperform a lighter motor at a higher KV under propeller load. Check the weight, size and maker’s thrust or power figures alongside KV.
Choosing a KV for your build
- Pick the battery voltage first. The motor and ESC must handle the pack’s full-charge voltage, not just the nominal figure.
- Pick the propeller or load. Bigger propellers and heavier loads need more torque, which points to a lower KV. Smaller propellers and light loads suit a higher KV.
- Check the current. Use the maker’s current or thrust tables where they exist. Stay within the rated current of both the motor and the ESC.
- Check the ESC’s RPM limit. An ESC has a maximum electrical RPM. A high-KV motor on a high voltage can exceed it.
- Test at low throttle first. Secure the motor, run it at low throttle, and check temperature and current before you increase the load.
Common mistakes
- Choosing the highest KV because it sounds faster. A high-KV motor on a large propeller can overheat and draw too much current.
- Running a motor on a higher voltage because “KV times voltage means more speed.” The motor and ESC must be rated for that voltage.
- Comparing turn counts across different brands. Turn counts only compare within a family.
- Changing ESC timing settings without knowing the effect. Some ESCs let you adjust timing, which can change how the motor behaves. Follow the maker’s recommendations.
Where to go next
For a specific case, see how many turns is a 3300 KV motor?. For torque in more depth, see do brushless motors have more torque?. For the wiring, see how to connect a brushless motor to an ESC.