Circuit Theory

Circuit Analysis Basics: Voltage, Current and Sources

Learn voltage, current, resistance and the difference between ideal, dependent, DC and AC sources, plus the main tools used to analyze a circuit.

On this page
  1. Voltage, current and resistance
  2. Sources: the parts that supply energy
  3. Types of circuits
  4. The core analysis tools
  5. Circuits with capacitors, inductors and AC
  6. Power, energy and units
  7. A simple way to start

Voltage, current and resistance

Voltage, current and resistance describe almost every simple circuit.

  • Voltage (volts, V) is the energy per unit charge between two points. It is the push that moves charge. A 9 V battery gives 9 joules of energy to each coulomb of charge that passes through it.
  • Current (amperes, A) is the amount of charge passing a point each second. One ampere is one coulomb per second.
  • Resistance (ohms, Ω) is how strongly a component opposes current. Ohm’s law ties the three together: V = I × R.

Ohm’s law is the starting point for most calculations in this cluster. Rearranged, it gives I = V / R and R = V / I.

Sources: the parts that supply energy

A source puts energy into a circuit. Textbooks divide sources into two families.

Independent sources

An independent source produces a voltage or current that does not depend on anything else in the circuit.

  • An ideal voltage source keeps its terminal voltage the same, whatever current it has to supply.
  • An ideal current source keeps its current the same, whatever voltage appears across it.

Real sources are not ideal. A real battery behaves like an ideal voltage source in series with a small internal resistance, so its terminal voltage drops as the load current rises. A real current source is usually modeled as an ideal current source in parallel with a resistance.

Dependent (controlled) sources

A dependent source produces a voltage or current that depends on a voltage or current somewhere else in the circuit. They are drawn as diamonds, and they are used to model transistors and op-amps in small-signal analysis. There are four types:

Type Name Controlled by Output Gain units
VCVS Voltage-controlled voltage source Voltage Voltage Dimensionless
CCVS Current-controlled voltage source Current Voltage Ohms (transresistance)
VCCS Voltage-controlled current source Voltage Current Siemens (transconductance)
CCCS Current-controlled current source Current Current Dimensionless

When you analyze a circuit with a dependent source, keep it active. Do not switch it off as you would an independent source. The superposition article covers this in more detail.

DC and AC sources

A DC source keeps a fixed polarity, so current flows one way. Batteries, solar cells and DC power supplies are common examples. An AC source reverses polarity periodically. Mains supply in the US is nominally 120 V RMS at 60 Hz (see Is US voltage AC or DC?). For more on DC sources, see What is a DC source?.

Types of circuits

Many lists claim there are “four types of electric circuits”, but there is no single standard list of four. Two common ways to sort circuits are:

  • By connection: series (one path, the same current through every part), parallel (components share the same two nodes, so the same voltage across each), and series-parallel (a mix of both).
  • By path: closed (a complete loop, so current can flow) or open (a break in the loop, so no steady current flows).

The core analysis tools

Once you know the sources and components, a handful of methods solve most problems:

  1. Ohm’s law and the series and parallel rules for simplifying resistor networks.
  2. Voltage dividers for splitting a source voltage between two resistors. See Voltage Divider Formula With Worked Examples.
  3. Kirchhoff’s laws. The currents entering a node sum to zero, and the voltages around a loop sum to zero. See Kirchhoff’s Voltage and Current Laws Explained With Examples.
  4. Superposition. In a linear circuit, solve one source at a time and add the results. See Superposition Theorem Explained With a Worked Example.
  5. Thevenin’s theorem. Reduce any linear network, seen from two terminals, to one voltage source and one series resistor. See Thevenin’s Theorem: How to Reduce Any Circuit to One Source and One Resistor.

Circuits with capacitors, inductors and AC

Resistors behave the same at every moment. Capacitors and inductors store energy, so their behaviour depends on time or frequency.

Power, energy and units

Power is the rate at which energy is transferred, and it is measured in watts. One watt is one joule per second. In a resistor, power can be written as P = V × I, P = I² × R, or P = V² / R. The electrical power formulas article covers these in detail, and What is a joule of energy? explains the energy unit.

A simple way to start

  1. Name each source and note whether it is ideal, dependent, DC or AC.
  2. Mark the nodes and the loops.
  3. Choose a method: simplify the network, divide the voltage, apply Kirchhoff’s laws, or use Thevenin’s theorem.
  4. Check the answer. Do the loop voltages sum to zero? Do the currents at each node balance? Does the power supplied equal the power used?

Keep exploring

Guides from other topics

All topics →