Circuit Theory

Superposition Theorem Explained With a Worked Example

Superposition theorem explained with a step-by-step worked example, showing how to solve one source at a time and why power cannot be superposed.

On this page
  1. What the superposition theorem says
  2. Steps
  3. Worked example
  4. Power does not superpose
  5. Common mistakes
  6. When to use it

What the superposition theorem says

In a linear circuit with several independent sources, any branch current or node voltage equals the algebraic sum of the contributions from each source acting alone. To find one source’s contribution, set every other independent source to zero:

  • A voltage source set to zero becomes a short circuit.
  • A current source set to zero becomes an open circuit.

Dependent sources stay in the circuit, because their output depends on the circuit’s own voltages or currents.

A circuit is linear when its output is proportional to its input and the effects add. Resistors, capacitors, inductors and ideal sources are linear. Diodes and transistors, used outside their linear ranges, are not.

Steps

  1. Pick one independent source and turn all the others off.
  2. Solve the circuit for the quantity you need.
  3. Repeat for each source.
  4. Add the results algebraically, keeping track of direction and sign.

Worked example

Two sources feed a common node X. V1 = 12 V sits in series with R1 = 2 Ω. V2 = 6 V sits in series with R2 = 2 Ω. A third resistor, R3 = 2 Ω, runs from node X to ground. Find the voltage at X.

Step 1: V1 on, V2 off. Replace V2 with a short. R2 now connects node X to ground through the short, so R2 and R3 are in parallel: 2 Ω ∥ 2 Ω = 1 Ω. This is a divider with R1:

V_X1 = 12 V × 1 Ω / (2 Ω + 1 Ω) = 4 V

Step 2: V2 on, V1 off. Replace V1 with a short. Now R1 and R3 are in parallel, which is again 1 Ω:

V_X2 = 6 V × 1 Ω / (2 Ω + 1 Ω) = 2 V

Step 3: Add the results. Both sources push in the same direction, so the contributions add:

V_X = 4 V + 2 V = 6 V

Check with nodal analysis. The currents into node X must balance:

(12 − V) / 2 + (6 − V) / 2 = V / 2

Solving gives V = 6 V, which matches. The current through R3 is 6 V / 2 Ω = 3 A. In the superposition steps, the current through R3 is 4 V / 2 Ω = 2 A from step 1 and 2 V / 2 Ω = 1 A from step 2. The currents add to 3 A.

Power does not superpose

Power depends on the square of voltage or current, so contributions from different sources do not add. In the example, the power in R3 with both sources on is:

P = (6 V)² / 2 Ω = 18 W

Adding the power from each step gives a different and wrong answer: 4² / 2 = 8 W, plus 2² / 2 = 2 W, which totals 10 W. Find the total voltage or current first, then calculate the power from it.

Common mistakes

  • Opening a voltage source, or shorting a current source. A voltage source is shorted when turned off, and a current source is opened.
  • Turning off a dependent source. Keep it active.
  • Ignoring direction. Each contribution has a sign. Add them with the sign that matches the chosen reference direction.
  • Using it on non-linear circuits, such as circuits with diodes in their non-linear region.
  • Adding power. As shown above, power does not superpose.

When to use it

Superposition is useful when a circuit has only a few sources and a clear structure. With many sources, nodal or mesh analysis is usually faster. Superposition and Thevenin’s theorem are often used together, for example to find the Thevenin voltage with each source acting alone.

For the rules behind the steps, see Kirchhoff’s Voltage and Current Laws. For a method that replaces a network with one source, see Thevenin’s Theorem. For the general picture, see Circuit Analysis Basics.

The complete guide to circuit theory

Circuit Analysis Basics: Voltage, Current and Sources
Read the guide

Keep exploring

Guides from other topics

All topics →