Circuit Theory

Voltage Divider Formula With Worked Examples

The voltage divider formula with worked examples, including what happens when a load is connected, and tips for choosing resistor values for a circuit.

On this page
  1. The voltage divider formula
  2. Worked example 1: unloaded divider
  3. Worked example 2: loaded divider
  4. Choosing resistor values
  5. Current division
  6. Limits of the divider

The voltage divider formula

Two resistors in series across a voltage source share that voltage in proportion to their resistances. The output is taken across the lower resistor, R2:

Vout = Vin × R2 / (R1 + R2)

The formula follows from two facts. The same current flows through both resistors, because they are in series. And the current is Vin / (R1 + R2). The voltage across R2 is that current multiplied by R2.

Worked example 1: unloaded divider

Let Vin = 12 V, R1 = 3 kΩ and R2 = 1 kΩ.

  • Total resistance: 3 kΩ + 1 kΩ = 4 kΩ
  • Current: 12 V / 4 kΩ = 3 mA
  • Output: Vout = 3 mA × 1 kΩ = 3 V

Check with the formula: 12 × 1 / (3 + 1) = 3 V. The voltage across R1 is 3 mA × 3 kΩ = 9 V, and 9 V + 3 V = 12 V, as Kirchhoff’s voltage law requires.

Worked example 2: loaded divider

Now connect a load of RL = 2 kΩ between the output and ground. The load sits in parallel with R2, so the bottom branch becomes:

R2 ∥ RL = (1 kΩ × 2 kΩ) / (1 kΩ + 2 kΩ) ≈ 0.667 kΩ

The new output is Vout = 12 × 0.667 / (3 + 0.667) ≈ 2.18 V.

The load pulls the output down from 3 V to about 2.18 V. A common rule of thumb is to make the load at least ten times R2, so the output stays close to the unloaded value. This is a guideline, not an exact limit.

Choosing resistor values

  • Divider current. Pick a current through the divider that is much larger than the load current. A common guideline is about ten times. A larger divider current keeps the output steadier, but it wastes more power.
  • Power in each resistor. Use P = I² × R to check ratings. For example, 3 mA through 3 kΩ dissipates (0.003 A)² × 3,000 Ω ≈ 0.027 W, so a standard 0.25 W resistor is more than enough.
  • Standard values. Use the nearest standard values, such as the E12 or E24 series, and then recheck the ratio with the actual values.

Current division

The same idea works for two resistors in parallel, but it divides current, not voltage. The current through R1 is:

I1 = I_total × R2 / (R1 + R2)

More current flows through the smaller resistor. For example, with R1 = 3 kΩ and R2 = 1 kΩ, the 3 kΩ branch carries I_total × 1 / (3 + 1) = 25% of the total current, and the 1 kΩ branch carries the other 75%.

Limits of the divider

  • The output is unregulated. If the load or the input changes, the output changes.
  • Source resistance matters. If the source has significant internal resistance, add it to R1.
  • AC circuits. With capacitors or inductors, replace each resistor with its impedance: Vout = Vin × Z2 / (Z1 + Z2).

A potentiometer is a variable voltage divider, which is why volume and brightness controls work this way.

For the rules this formula comes from, see Kirchhoff’s Voltage and Current Laws. For a loaded divider viewed from the load, see Thevenin’s Theorem.

The complete guide to circuit theory

Circuit Analysis Basics: Voltage, Current and Sources
Read the guide

Keep exploring

Guides from other topics

All topics →