Capacitors

How to find the value of a ceramic capacitor?

Read a ceramic capacitor's value from its three-digit code or shorthand like 4n7, decode the tolerance letter, and confirm with a meter. 104 means 100 nF.

On this page
  1. The short answer
  2. Reading the three-digit code
  3. Shorthand values
  4. Tolerance letters
  5. When the print is worn or missing
  6. Checking the value with a meter
  7. Key takeaways

The short answer

Most ceramic disc capacitors are marked with a three-digit code. The first two digits are significant figures. The third digit is the number of zeros to add, and the unit is picofarads (pF).

For example, 104 means 10 followed by four zeros, which is 100,000 pF. That equals 100 nF, or 0.1 µF.

Reading the three-digit code

Use the same rule for every three-digit code:

Code Calculation Value
101 10 × 10¹ pF 100 pF
102 10 × 10² pF 1,000 pF (1 nF)
103 10 × 10³ pF 10,000 pF (10 nF)
104 10 × 10⁴ pF 100,000 pF (100 nF, 0.1 µF)
105 10 × 10⁵ pF 1,000,000 pF (1 µF)
224 22 × 10⁴ pF 220,000 pF (220 nF, 0.22 µF)

If you are unsure whether a value is in pF, nF or µF, convert it to picofarads first. A value of 1,000 pF is the same as 1 nF.

Shorthand values

Larger ceramic discs often print the value in full, using a letter in place of the decimal point:

  • p means picofarads: 22p = 22 pF
  • n means nanofarads: 100n = 100 nF, and 4n7 = 4.7 nF
  • µ (or u) means microfarads: 0.1µ = 0.1 µF

Values below 10 pF may use R as the decimal point. For example, 8R2 means 8.2 pF.

Tolerance letters

A letter after the code shows the tolerance, which is how far the real value may differ from the printed one. The common letters are:

  • J: ±5%
  • K: ±10%
  • M: ±20%

Tolerance is about the spread around the value, not a sign of quality. Always check the datasheet if the tolerance matters for your design.

Some discs also print a voltage rating, such as 50V, or a dielectric code such as X7R. Read the voltage before you substitute a part, because a higher rating is safer and a lower one may not be.

When the print is worn or missing

Printing on small discs can rub off or be hard to read. Try these steps:

  1. Turn the part under a bright light and check both faces. Some discs print on one side only.
  2. Compare it with the circuit’s schematic or bill of materials, which often gives the value.
  3. Measure it with a meter that has a capacitance range. See how to test a capacitor with a multimeter for the steps.

Many surface-mount ceramic capacitors have no printed value at all, because the chips are too small. For these, use the design documents or the part’s datasheet.

Checking the value with a meter

A multimeter with a capacitance range is enough for a rough check. Discharge the capacitor first, and remove it from the circuit if you can. Expect the reading to differ from the marked value, because tolerance, temperature and applied voltage all affect ceramic capacitance. A reading far from the expected value suggests a faulty part, but a small difference does not on its own.

Key takeaways

  • A three-digit code gives the value in picofarads: first two digits, then the number of zeros.
  • 104 = 100 nF = 0.1 µF, and 103 = 10 nF.
  • Shorthand such as 4n7 uses the letter in place of the decimal point.
  • The letter after the code gives the tolerance: J is ±5%, K is ±10% and M is ±20%.
  • Many SMD ceramic capacitors are unmarked, so use the datasheet or a meter.

For the full range of marking styles, including electrolytic and SMD codes, see capacitor codes and markings. Ceramic discs are non-polarized, so they do not need the orientation checks described in capacitor polarity.

The complete guide to capacitors

Capacitors Explained: How They Behave in DC and AC Circuits
Read the guide

Keep exploring

Guides from other topics

All topics →