Capacitors

Capacitor Leakage Current: What It Is and When It Matters

Capacitor leakage current explained: the small DC current through the dielectric, how it varies by type, and why it matters in timing and battery circuits.

On this page
  1. What leakage current is
  2. Modeling leakage as insulation resistance
  3. How leakage varies by capacitor type
  4. Datasheet leakage figures
  5. What raises leakage
  6. Why it matters in circuits
  7. How to measure it
  8. Key takeaways

What leakage current is

A capacitor is not a perfect insulator between its plates. A very small direct current always flows through the dielectric once a voltage is applied. This is called leakage current.

It is usually small, often in the nanoamp to microamp range, but it matters in circuits that need to hold a charge or carry very little current.

Modeling leakage as insulation resistance

Leakage can be modeled as a very high resistance, the insulation resistance (R_iso), in parallel with an ideal capacitor:

I_leak = V / R_iso

For example, 10 V across 100 MΩ gives I = 10 / 100,000,000 = 0.1 µA. The higher the insulation resistance, the smaller the leakage.

How leakage varies by capacitor type

  • Electrolytic and tantalum: these typically leak more. Their datasheets often give a maximum leakage value, measured after a set time, so the oxide layer has time to stabilize.
  • Ceramic and film: these usually leak much less. Their datasheets often give insulation resistance in megohms or gigohms, or a CR product in MΩ·µF, which describes the time constant of the leakage.

For a circuit that depends on low leakage, a ceramic or film part is usually the better choice. See tantalum vs electrolytic capacitors for how the electrolytic types compare.

Datasheet leakage figures

Electrolytic datasheets often specify a maximum leakage current as a formula based on the capacitance and voltage, such as I_leak ≈ k × C × V. The constant k and the form of the formula vary by manufacturer and part, so use the figure for the part you are using. The figure is usually given after a set time, often a few minutes, because the leakage falls over the first minutes after voltage is applied.

Ceramic and film datasheets give insulation resistance or a CR product instead. A high CR product means low leakage, and it is a good figure to compare when choosing a part.

What raises leakage

  • Higher voltage: leakage rises as the applied voltage approaches the rating.
  • Higher temperature: heat increases the conduction through the dielectric.
  • Thinner dielectric or smaller packages: these can have lower insulation resistance.
  • Aging or storage: an electrolytic that has been stored for a long time may show higher initial leakage, and a worn part can leak more as it degrades.

Why it matters in circuits

Standby and battery life

In battery-powered and standby circuits, leakage can drain a stored charge slowly. A capacitor that holds a backup voltage for a clock or a memory chip may discharge sooner than expected if its leakage is high.

Timing, sample-and-hold and high-impedance inputs

Timing and sample-and-hold circuits rely on a capacitor holding its charge for a set time. Leakage causes the voltage to drift, which shifts the timing or the held value. High-impedance inputs, such as some sensor or measurement front ends, are also sensitive to small leakage currents.

DC offset in coupling stages

A coupling capacitor passes the AC signal while blocking DC. If leakage lets a small DC current through, the bias of the following stage can shift over time, which can affect the signal. This is one reason low-leakage film parts are often chosen for coupling.

How to measure it

Leakage is measured with a DC supply, a sensitive ammeter in series, and a set settle time at the test voltage. Some labs use an insulation resistance tester. A basic multimeter is not suitable for leakage measurement, because its input and test currents are too coarse for the very small values involved.

Discharge the capacitor before connecting it to a test setup, and keep to the voltage limits of the part.

Key takeaways

  • Leakage current is a small DC current that flows through the dielectric when a voltage is applied.
  • It can be modeled as a high insulation resistance in parallel with the capacitor.
  • Electrolytic and tantalum parts leak more than ceramic and film parts.
  • Leakage matters in standby, timing, sample-and-hold, high-impedance and coupling circuits.
  • Check the datasheet for the part’s leakage figure, and do not expect a basic multimeter to measure it.

The complete guide to capacitors

Capacitors Explained: How They Behave in DC and AC Circuits
Read the guide

Keep exploring

Guides from other topics

All topics →