Capacitors

What are polypropylene capacitors used for?

What polypropylene capacitors are, why low loss and stable capacitance suit audio, motors and power electronics, and how they differ from polyester film parts.

On this page
  1. What a polypropylene capacitor is
  2. Why engineers choose polypropylene
  3. Common uses
  4. Polypropylene (CBB) vs polyester (CL)
  5. How to recognize one
  6. Mains-rated parts need a safety rating
  7. Key takeaways

What a polypropylene capacitor is

A polypropylene capacitor is a film capacitor. Its dielectric is a thin sheet of polypropylene plastic, and its electrodes are either thin metal foil or a very thin metal coating deposited on the film. The film is wound into a roll, encapsulated and fitted with leads.

Two common forms are:

  • Foil-type polypropylene: the electrodes are metal foil layers.
  • Metalized polypropylene (MKP): a thin metal layer on the film. Metalized parts can recover from small internal faults, a property called self-healing, which is why they are widely used.

Polypropylene capacitors are non-polarized, so they can be connected in either direction. Their schematic symbol is the plain two-line symbol used for all non-polarized parts.

Why engineers choose polypropylene

Polypropylene is popular because it combines several useful properties:

  • Low dielectric loss: It wastes little energy as heat, especially at audio and higher frequencies.
  • Stable capacitance: Its value changes little with temperature and frequency, compared with many other dielectrics.
  • High insulation resistance: Leakage current is very small.
  • Good AC and pulse performance: Film construction handles repeated voltage reversals and fast edges well.

These properties come with trade-offs. Polypropylene parts are often larger for a given capacitance than polyester parts, and they cost more.

Common uses

Audio crossovers and coupling

In loudspeaker crossovers, polypropylene capacitors are a common choice because their low loss and stable value keep the sound consistent. They are also used for signal coupling, where a capacitor blocks DC while passing audio. See capacitors in audio for crossover sizing.

Motor run and start capacitors

Single-phase AC motors, such as those in fans, pumps and some compressors, often use polypropylene run capacitors. These capacitors help create the phase shift the motor needs to run smoothly. They work with AC voltage and must be rated for it. A run capacitor stores energy at mains voltage, even after it is disconnected, so treat it with the same care as any high-voltage part.

Snubbers and power electronics

In power electronics, polypropylene capacitors are used in snubber circuits across switching devices, where they absorb voltage spikes. They also appear in DC-link positions in some inverters, where their low loss and high ripple handling are useful. These uses are specialist, so check the design requirements rather than substituting a generic part.

Timing, filtering and pulse circuits

Where timing accuracy matters, the stable value of a polypropylene part helps keep the timing constant over temperature. The same property makes them useful in filters and in pulse circuits, where the capacitor must handle fast voltage changes.

Polypropylene (CBB) vs polyester (CL)

Polypropylene film parts are often compared with polyester film parts. The two look similar, but they differ in several ways:

  • Polypropylene (CBB, or MKP on the label) generally has lower loss and more stable capacitance across temperature and frequency.
  • Polyester (CL, or MKT on the label) is generally smaller for the same value and less expensive.
  • Polypropylene is usually the better choice for audio and power work where loss and stability matter. Polyester is often adequate for general-purpose filtering.

Figures for loss and stability vary by manufacturer. Check the datasheet for the part you plan to use rather than relying on general comparisons.

How to recognize one

Look at the label on the body. Common codes include:

  • MKP: metalized polypropylene
  • MPP: metalized polypropylene (another code some makers use)
  • CBB: polypropylene, often used in Chinese part numbers
  • PP: polypropylene

Some parts are labeled only with a value and voltage. In that case, the datasheet or the schematic’s bill of materials will tell you the dielectric.

Mains-rated parts need a safety rating

A polypropylene capacitor is not automatically safe to connect across mains power. Parts used for mains filtering need a safety rating:

  • X-class capacitors are rated for line-to-line use across the mains.
  • Y-class capacitors are rated for line-to-earth use, where a failure must not create a shock path.

Generic film capacitors do not carry these ratings. Use only parts that are marked with the appropriate safety class and approved for the application. If you are not sure whether a part is safety-rated, do not use it on mains.

Key takeaways

  • Polypropylene capacitors are non-polarized film parts with low loss and stable capacitance.
  • They are common in audio crossovers, motor run capacitors, snubbers and timing circuits.
  • Compared with polyester, polypropylene is usually more stable and lower loss, and polyester is usually smaller and cheaper.
  • Recognize them by labels such as MKP, MPP, CBB and PP.
  • Mains filtering needs X- or Y-class safety-rated parts, not a generic film capacitor.

The complete guide to capacitors

Capacitors Explained: How They Behave in DC and AC Circuits
Read the guide

Keep exploring

Guides from other topics

All topics →