Components and Schematics

Resistor Color Codes Explained: How to Read 4-Band and 5-Band Resistors

Read 4-band and 5-band resistor color codes step by step, with a color chart, worked examples, and tips for checking your reading with a meter.

On this page
  1. Short answer
  2. Find the tolerance band first
  3. The color chart
  4. Reading a 4-band resistor
  5. Reading a 5-band resistor
  6. Six-band resistors
  7. Surface-mount resistors use numbers
  8. Check your reading with a multimeter
  9. Common mistakes

Short answer

Hold the resistor so the gold or silver tolerance band is on the right, and read from left to right. On a 4-band resistor, the first two bands are digits, the third is the multiplier, and the fourth is the tolerance. On a 5-band resistor, the first three bands are digits, the fourth is the multiplier, and the fifth is the tolerance.

Find the tolerance band first

Most resistors have a tolerance band in gold (±5%) or silver (±10%). The tolerance band is usually set slightly apart from the other bands. Place it on the right. If there is no gold or silver band, the tolerance is often ±20%, and the reading order can be harder to confirm. In that case, measure the resistor with a meter, as described below.

The color chart

Color Digit Multiplier Tolerance
Black 0 ×1 —
Brown 1 ×10 ±1%
Red 2 ×100 ±2%
Orange 3 ×1,000 —
Yellow 4 ×10,000 —
Green 5 ×100,000 ±0.5%
Blue 6 ×1,000,000 ±0.25%
Violet 7 ×10,000,000 ±0.1%
Gray 8 ×100,000,000 ±0.05%
White 9 ×1,000,000,000 —
Gold — ×0.1 ±5%
Silver — ×0.01 ±10%

Reading a 4-band resistor

The first two bands give two digits, which form a number. Multiply that number by the multiplier band, and the tolerance band gives the accuracy.

Yellow, violet, red, gold: the digits are 4 and 7, which form 47. The red multiplier is ×100, so the value is 4,700 Ω, or 4.7 kΩ. Gold means ±5%.

Red, red, brown, gold: the digits are 2 and 2, which form 22. The brown multiplier is ×10, so the value is 220 Ω. Gold means ±5%.

Reading a 5-band resistor

Five-band resistors give three digits, a multiplier, and a tolerance. They are often used where the tolerance needs to be tighter.

Brown, black, black, red, brown: the digits are 1, 0, and 0, which form 100. The red multiplier is ×100, so the value is 10,000 Ω, or 10 kΩ. Brown means ±1%.

Six-band resistors

Some resistors have a sixth band. It gives the temperature coefficient, in parts per million per degree Celsius, and it is read last. It matters mostly in precision circuits, so beginner projects rarely need to check it.

Surface-mount resistors use numbers

Small surface-mount resistors are usually marked with a three- or four-digit number rather than bands. In a three-digit code, the first two digits are the value and the third is the power of ten. For example, 103 means 10 × 10³ = 10,000 Ω, or 10 kΩ. An R stands for a decimal point, so 4R7 means 4.7 Ω.

Check your reading with a multimeter

Set the meter to resistance (Ω) and touch one probe to each lead. Compare the reading with the value from the color code. A resistor in a circuit can read low because other parts are in parallel with it, so lift one leg or remove the part before trusting the reading.

Once you have the value, the LED current-limiting resistor guide shows how to choose a resistor for an LED. For what a resistor does in a circuit, see the definitions of resistors, inductors, and capacitors.

Common mistakes

  • Reading from the wrong end. A 4-band resistor read backward gives the wrong value. Find the tolerance band first.
  • Confusing similar colors. Brown and red, orange and yellow, and blue and violet are easy to mix up, especially under dim light. A magnifier and a good light help.
  • Assuming a 3-band resistor is precise. Three-band resistors usually have a tolerance of ±20%.
  • Trusting an in-circuit reading. Parallel paths through other parts can make the resistor look smaller than it is.

The complete guide to components and schematics

Electronic Components Explained: Active vs Passive
Read the guide

Keep exploring

Guides from other topics

All topics →