Components and Schematics

Schematic Labels Decoded: GND, VSS, VDD and NO/NC

Decode common schematic labels: GND and other ground labels, VCC, VDD and VSS on chips, NO/NC on switches and relays, and what the letter N can mean.

On this page
  1. Ground labels: GND, G, GR, PE and FG
  2. VCC, VDD, VSS and VEE on chips
  3. NO and NC on switches and relays
  4. NC on a board can mean “not connected”
  5. What the letter N can mean
  6. Reading labels on a real schematic

Ground labels: GND, G, GR, PE and FG

On electronics schematics, the usual label for the 0 V reference is GND. It marks the common return path that current flows back through, and it is the reference point for voltage measurements. Electrical drawings for buildings and industrial panels use other labels for ground.

  • GND: the 0 V reference and common return in circuit schematics.
  • G: a common abbreviation for ground on electrical drawings, panels, and outlets.
  • GR: sometimes used for an equipment grounding terminal.
  • PE (Protective Earth): safety earthing in international and industrial wiring, meant to protect people from electric shock.
  • FG (Frame Ground): a chassis or enclosure connection, often used for shielding or safety.

A GND symbol on a circuit diagram is a reference point. It is not always the same thing as a safety earth. A battery-powered circuit can have a GND reference that is not connected to earth at all.

Without a shared reference, a circuit has no meaningful absolute voltages, so readings are hard to interpret and parts can behave unpredictably. In mains equipment, the protective earth is a safety feature and should not be removed or bypassed.

VCC, VDD, VSS and VEE on chips

Supply labels on chip datasheets and schematics depend on the transistor technology inside the chip.

  • VCC: the positive supply for chips built with bipolar transistors. The name refers to the collector supply. It is now used loosely for the positive supply on many chips.
  • VEE: the negative supply for bipolar chips. The name refers to the emitter supply.
  • VDD: the positive supply for chips built with MOS transistors, which includes most CMOS logic. The name refers to the drain supply.
  • VSS: the negative or ground supply for MOS chips. The name refers to the source supply. In most single-supply digital circuits, VSS is tied to ground.

So VCC and VDD are both positive supply labels, and in many modern chips they mean the same thing in practice. VSS does not always equal GND. In a circuit with a positive and a negative supply, the negative rail can sit below ground. Check the datasheet rather than assuming.

NO and NC on switches and relays

NO means normally open. The contacts are apart in the resting state and touch when the switch or relay is actuated.

NC means normally closed. The contacts touch in the resting state and separate when actuated.

A switch body often has three terminals: C (common), NO, and NC. With the switch at rest, a wire between C and NO gives an open circuit, and a wire between C and NC gives a closed circuit. A continuity check with a multimeter will confirm which is which. The relay guide explains how these contacts behave inside a relay.

NC on a board can mean “not connected”

On integrated circuit and board schematics, NC often means not connected. It marks a pin with no internal electrical connection. Leave such a pin unconnected unless the datasheet says otherwise. The same two letters can therefore mean normally closed on a switch and not connected on a chip.

What the letter N can mean

The letter N appears in several places, and it does not always mean the same thing.

  • Mains wiring: N usually means neutral, the return conductor for AC. Wire colors vary by country. In North America the neutral is typically white, and in the UK and much of Europe it is typically blue.
  • Switches: N is not used. NO and NC are the labels that matter.
  • Chip pins: the letter may appear in a pin name, so read the datasheet’s pin table instead of guessing.

Mains wiring can be lethal. Do not work on mains circuits unless you are trained and qualified to do so. If you are unsure, use a licensed electrician.

Reading labels on a real schematic

  1. Check the title block and legend for the drawing’s conventions.
  2. Find the ground symbol and the supply labels, and note which rails are positive and which are negative.
  3. For each switch or relay, check whether NO or NC is used, and what state the contacts are in at rest.
  4. For chip pins, consult the datasheet before connecting NC or unused pins.

The schematic symbols guide covers the shapes of the parts themselves, and how a relay works shows NO and NC contacts in a working part.

The complete guide to components and schematics

Electronic Components Explained: Active vs Passive
Read the guide

Keep exploring

Guides from other topics

All topics →