Power Supplies

How to Set the Current Limit on a Bench Power Supply

Set a bench supply's current limit safely: short the outputs, set the limit, then set the voltage. Learn what constant current mode means for your circuit.

On this page
  1. Short answer
  2. What the current limit does
  3. What you need
  4. Step by step
  5. Choosing a limit
  6. Reading the CC and CV indicators
  7. Common mistakes
  8. What a current limit cannot do
  9. Homemade limiters

Short answer

Set the current limit before you connect your circuit. Turn the voltage to its minimum, short the output leads together, and turn the output on. Adjust the current knob until the display shows the limit you want, and the constant-current (CC) indicator lights. Then turn the output off, remove the short, set the voltage you need, and connect the circuit.

What the current limit does

A current limit caps how much current the supply can deliver. Under normal load, the supply holds the set voltage. This is constant voltage (CV) mode. If the load tries to draw more than the limit, the supply switches to constant current (CC) mode. It holds the current at the limit, and the output voltage falls.

That is why a fault, such as a short or a wrong connection, shows up as a falling voltage and a CC light, rather than a rising current.

What you need

  • The bench supply and its leads.
  • A short lead or a pair of clips to short the outputs.
  • A multimeter, if you want to check the displayed values.
  • The circuit’s datasheet, or your estimate of how much current it draws.

Step by step

  1. Turn the voltage knob to its minimum, and turn the output off.
  2. Short the outputs by touching the positive and negative leads together. Keep the voltage at minimum while you do this.
  3. Turn the output on. The supply should now be in CC mode, because the short draws current up to the limit.
  4. Turn the current knob until the display shows the limit you want, such as 100 mA.
  5. Turn the output off and remove the short.
  6. Turn the voltage up to the level you need, and check it on the display.
  7. Connect your circuit, and watch the CC and CV indicators.

Some supplies use a slightly different order. Check the manual for your model.

Choosing a limit

  • Start from the expected current. Use the circuit’s datasheet or your own calculation.
  • Leave some margin. Set the limit above the normal draw, so that normal operation does not trigger CC mode. Do not set it so high that a fault could damage components.
  • Start low for a new circuit. If CC mode triggers, investigate before you raise the limit.

A current limit is not a substitute for a fuse, correct wiring or the right voltage.

Reading the CC and CV indicators

  • CV (constant voltage): the supply holds the set voltage. This is normal.
  • CC (constant current): the supply holds the current at the limit, and the voltage falls. The circuit is drawing more than the limit, or it has a fault.

If the CC light comes on as soon as you connect a circuit, check the circuit’s connections before you raise the limit.

Common mistakes

  • Forgetting to set the limit before connecting the circuit.
  • Leaving the limit at its maximum. A fault can then draw full current.
  • Setting the limit so low that the circuit cannot start. The output then looks dead, and it is worth checking the CC light first. The no output troubleshooting guide covers that case.
  • Shorting the outputs while the voltage is set high.
  • Assuming the current limit protects the circuit from a wrong voltage. It does not.

What a current limit cannot do

  • Some supplies react slowly, so a very fast short can still produce a brief peak.
  • It does not stop an overvoltage, or protect against reverse polarity.
  • It does not replace fuses, correct wiring or a check of the circuit before you power it.

Homemade limiters

Some published designs build a current limiter from a regulator, such as an L200, with resistors setting the limit. These are useful for learning how a limit works, but a commercial bench supply is safer and easier to trust. The linear power supply circuits guide covers the regulator basics behind such designs.

For the wider picture of CV and CC supplies, see DC power supplies explained.

The complete guide to power supplies

DC Power Supplies Explained: Linear, Switching and Variable
Read the guide

Keep exploring

Guides from other topics

All topics →