Power Supplies

Simple Voltage Boosting Circuits: Joule Thief and Diode-Capacitor Multipliers

See how a joule thief boosts a nearly flat cell to light an LED, how diode-capacitor voltage multipliers work, and the safety limits of both circuits.

On this page
  1. Two simple ways to raise a voltage
  2. How a joule thief works
  3. What a joule thief is good for
  4. Why “high power” joule thief designs are a poor fit
  5. Diode-capacitor voltage multipliers
  6. Safety: why multipliers are not for mains
  7. Choosing between them

Two simple ways to raise a voltage

A joule thief and a diode-capacitor voltage multiplier both raise a voltage, but they work differently. Neither is a regulated power supply. Their output depends on the load and the source, so treat them as demonstration circuits rather than power sources you can rely on.

How a joule thief works

A joule thief is a single-transistor blocking oscillator. A transistor switches current through a small inductor, usually wound on a ferrite core, and a feedback winding turns the transistor on and off many times a second. Each time the transistor cuts off, the inductor’s stored energy pushes the voltage above the battery’s. A diode takes that energy and passes it to an LED or a small capacitor.

This is why a joule thief can light an LED from a cell that is too flat to light it directly. The circuit takes most of the cell’s remaining energy, even at a low voltage.

What a joule thief is good for

It is a poor choice for:

  • Powering electronics that need a stable voltage. The output rises and falls with the battery and the load.
  • Anything with a meaningful current draw. The output falls apart as the load increases.
  • Motors, microcontroller boards, or any load where a fault could cause harm.

Why “high power” joule thief designs are a poor fit

Searches for “high power joule thief” lead to designs with bigger transistors and more turns on the core. The limits are the core’s saturation point, the transistor’s power dissipation and the battery’s capacity. More power means more heat and faster battery drain. With rechargeable lithium cells, it also means a real risk of deep-discharge damage and overheating.

If you need more power from a battery, use a tested boost converter module rated for the job. The types of power converters article explains how converters are sized and why their ratings matter.

Diode-capacitor voltage multipliers

A voltage multiplier stacks AC peaks, using diodes and capacitors, into a higher DC voltage. The simplest version is the half-wave voltage doubler:

  • On one half-cycle, the first diode charges the first capacitor to the peak of the input.
  • On the other half-cycle, the second diode charges the second capacitor to the input peak plus the voltage on the first capacitor.
  • The voltage across the second capacitor is roughly twice the input peak, less a diode drop for each diode.

A tripler and a quadrupler add more stages. Each stage adds voltage, but it also adds ripple and reduces the current the circuit can supply.

Under load, the output drops. The capacitors give up charge between the peaks, so the output sags and ripples more as the current rises. A multiplier is a poor source for anything that draws steady current.

Safety: why multipliers are not for mains

Multipliers are used to make high voltages from transformers, and that is exactly why they are hazardous.

  • Built from mains, a multiplier produces lethal voltages. Its capacitors keep a charge after unplugging.
  • Use only low-voltage AC sources that you understand. Even a low-voltage transformer can be unsafe if its primary is connected to mains and you handle it carelessly.
  • Choose diodes and capacitors with voltage ratings well above the expected peak.
  • Discharge the capacitors through a suitable resistor before you touch the circuit.
  • Keep the circuit off the mains and out of reach of children and pets.

Commercial high-voltage supplies use multipliers too, but they are built with designed insulation, interlocks and components rated for the job. Hobby parts are not a substitute.

Choosing between them

Goal Better choice Why
One LED from a nearly flat cell Joule thief Designed for low power from a weak cell
Higher DC from a low-voltage AC source Diode-capacitor multiplier Simple, but expect poor regulation and ripple
Stable higher DC from a DC battery Boost converter module Regulated and rated for the load

For the converter options, see types of power converters. For why a higher voltage can damage a device, see can you use a higher voltage power adapter.

The complete guide to power supplies

DC Power Supplies Explained: Linear, Switching and Variable
Read the guide

Keep exploring

Guides from other topics

All topics →