Power Supplies

Why a 7805 Voltage Regulator Gets Hot and How to Cool It

A 7805 runs hot because it turns the spare voltage into heat. Learn the power formula, common causes and fixes, including heatsinks and input voltage.

On this page
  1. Short answer
  2. Why a 7805 makes heat
  3. Calculate the heat
  4. Common causes
  5. Measure before you act
  6. Fixes
  7. Safety

Short answer

A 7805 gets hot because it is a linear regulator. It keeps the output at 5 V by turning the extra input voltage into heat. The power it has to get rid of is (input voltage − 5 V) × load current. If that figure is high, the regulator is hot by design, and a heatsink or a lower input voltage helps. If it is hot at a light load and a sensible input, look for a fault.

Why a 7805 makes heat

The 7805 holds its output at 5 V by dropping the difference across an internal pass element. The energy that does not reach the load is converted to heat inside the package. This is how linear regulators work, so heat alone does not mean the part is faulty.

Calculate the heat

The power dissipated is:

P = (Vin − Vout) × Iout

With Vout = 5 V, here are three examples:

  • 9 V in, 0.5 A load: (9 − 5) × 0.5 = 2 W.
  • 12 V in, 1 A load: (12 − 5) × 1 = 7 W.
  • 15 V in, 1 A load: (15 − 5) × 1 = 10 W.

A 7805 in a TO-220 package without a heatsink cannot shed 7 to 10 W comfortably. Figures like these need a large heatsink, or a different approach.

Common causes

  1. Input voltage too high. This is the most common cause. An unregulated input from a transformer, rectifier and reservoir capacitor can sit well above the transformer’s nominal voltage, especially at light load. Measure the input both with and without the load.
  2. Load current higher than expected. Measure what the circuit really draws, rather than what the design assumed.
  3. No heatsink, or poor thermal contact. A heatsink needs a firm mounting and, usually, thermal compound.
  4. Missing or wrong capacitors. Without the datasheet capacitors close to the regulator, it can oscillate, and oscillation produces heat.
  5. A short or fault in the load. A short makes the regulator reach its current limit, and it heats up.
  6. A damaged or counterfeit part. If the circuit is otherwise correct and the regulator still runs hot, replace it.

Measure before you act

  • Input voltage at the regulator’s input pin, with the load connected.
  • Output voltage at the output pin. It should read close to 5 V.
  • Load current, if you can measure it.
  • How hot it gets, and how quickly, with care.

Interpret the readings against the formula. A 7805 with a moderate input, supplying around 100 mA, dissipates well under 1 W. If it is too hot to hold for more than a couple of seconds even with a heatsink, look at the input voltage, the capacitors and the wiring. Do not assume the part is simply too small.

Fixes

  • Lower the input voltage. Choose a transformer whose DC input sits a few volts above 5 V plus the regulator’s dropout, which is about 2 V for a 7805. Heat falls in direct proportion to the voltage gap.
  • Add a heatsink sized for the worst-case dissipation, and use thermal compound. The metal tab of a 7805 in a TO-220 package is its ground pin. Use an insulating washer if the heatsink must not be grounded.
  • Use a different regulator for a large drop. A low-dropout (LDO) 5 V regulator allows a lower input, which reduces heat. The formula still applies. A switching buck module converts a large drop with far less heat, but brings the noise trade-offs in what the disadvantages of SMPS are. The types of power converters article explains the buck family.
  • Fit the datasheet capacitors, about 0.33 µF at the input and 0.1 µF at the output, as close to the regulator as you can.
  • Replace the part if it is faulty, or if its markings look wrong.

For the full build of a 7805 supply, including transformer choice and reservoir capacitor rating, see DIY linear power supply circuits.

Safety

  • A hot regulator can burn you. Let it cool before you handle it.
  • Do not run a hot regulator inside a closed enclosure without ventilation or a heatsink.
  • If the regulator is hot with the load disconnected, check the input and output for a short before powering up again.

For the basics of linear and switching supplies, see DC power supplies explained.

The complete guide to power supplies

DC Power Supplies Explained: Linear, Switching and Variable
Read the guide

Keep exploring

Guides from other topics

All topics →