Power Supplies

ATX Power Supply Jumper Test: How to Power On and Test a PSU

Learn the ATX power supply jumper test: bridge the green PS_ON wire to ground, read the fan result, and see what the test misses and how to stay safe.

On this page
  1. What the jumper test checks
  2. What you need
  3. Step by step
  4. Reading the result
  5. What the jumper test misses
  6. Is there a way to check a PSU without opening the PC?
  7. How to tell if your PC needs a new power supply
  8. Safety
  9. Next steps

What the jumper test checks

The ATX standard uses a signal called PS_ON (power supply on). A motherboard switches the PSU on by pulling PS_ON to ground. On the 24-pin connector, the PS_ON wire is green, and the ground wires are black.

The jumper test copies that signal. With the PSU’s mains switch on, bridging the green wire to a black wire tells the PSU to start. If the fan spins, the PSU powers on without a motherboard. That is a narrow result. It does not show that the PSU’s voltages are correct or stable under load.

What you need

  • The PSU, removed from the PC, or at least fully disconnected from the motherboard, graphics card and drives.
  • A bent paperclip or a commercial PSU jumper plug.
  • A dry, non-conductive, non-flammable work surface.
  • Optional: a PSU tester or a multimeter, for voltage checks after the fan test.

Step by step

  1. Unplug the PSU from the wall and set its rear switch to off (O).
  2. Disconnect everything. Remove the 24-pin cable and all other cables from the PSU.
  3. Find the green wire and a black wire. On the 24-pin connector, the green wire is PS_ON and the black wires are ground. Use your PSU’s pinout diagram to locate them. Do not rely on pin numbers from memory, because guides disagree on the numbering.
  4. Bridge them with the paperclip or jumper plug. Keep the jumper clear of other pins and of anything metal.
  5. Plug in the AC cord and switch the PSU on (I).
  6. Watch and listen. A spinning fan means the PSU powers on. If you smell burning, see smoke, or hear buzzing or clicking, switch off and unplug at once.
  7. Switch off, unplug, and remove the jumper before you touch anything else.

Some PSUs with zero-RPM or eco modes spin the fan only briefly, or need a small load such as a case fan before the fan runs steadily.

Reading the result

  • The fan spins and keeps spinning. The PSU powers on. This is a good sign, but it is not proof that the PSU is healthy.
  • The fan spins briefly and stops. It may be in an eco or zero-RPM mode, or a protection may have tripped. Check the PSU’s manual before drawing a conclusion.
  • No fan and no sound. The PSU may be dead, the fuse may have blown, a switch may be faulty, or the mains connection may be poor. Do not keep retrying. Have it checked, or replace it.
  • The fan spins, but the unit smells, heats up or makes odd noises. Stop and replace it.

What the jumper test misses

The jumper test does not show:

  • Whether the voltages on the 12 V, 5 V and 3.3 V rails are accurate.
  • Ripple, or how the voltages hold up under load.
  • Slow faults, such as ageing capacitors.

Many crashes and shutdowns only happen under heavy load, such as gaming. A PSU tester that plugs into the connectors is the easiest way to read the voltages. Multimeter readings on a running PSU need care. Only attempt them if you understand how to work safely with powered equipment.

If the PSU passes and the PC still will not start, the motherboard or another component may be at fault. The motherboard multimeter guide covers the next checks.

Is there a way to check a PSU without opening the PC?

Not really. The jumper test needs the 24-pin cable disconnected from the motherboard. Testing a PSU in practice means disconnecting it from the PC, so opening the case is normally part of the job. You can take the PSU out, test it on a bench, and refit it afterwards.

How to tell if your PC needs a new power supply

These signs point toward the PSU, but they are not conclusive:

  • Random shutdowns or restarts, especially under load.
  • The PC will not start, and the PSU fails the jumper test.
  • A burning smell, crackling, or a loud or changing noise from the PSU.
  • Visible damage to the PSU or its cables.

Other parts, such as the motherboard, memory or graphics card, can cause the same symptoms. Test before you buy.

Safety

  • Mains is lethal. The PSU’s mains side can hold charge, so do not open the PSU case.
  • Prepare the bench with the PSU unplugged. Work on a dry, non-conductive surface.
  • Never leave a bridged PSU powered on and unattended.
  • Keep the jumper away from metal, and remove it as soon as the test is over.
  • Do not test a PSU that is damaged, smells of burning, or has a frayed cord. Replace it.
  • If you are not comfortable with any of this, use a PC repair service.

Next steps

If the PSU does not power on, the no output from a power supply guide gives the checks in order. For the basics of how PSUs convert and regulate power, see DC power supplies explained.

The complete guide to power supplies

DC Power Supplies Explained: Linear, Switching and Variable
Read the guide

Keep exploring

Guides from other topics

All topics →