Short answer
If a power supply gives no output, check the simple things first: the outlet, the cord and plug, the switches, the fuse, the output setting and the connector. Then measure the output with a multimeter. Many “no output” cases turn out to be a simple fault. If the unit shows no sign of life at all, with no lights, fan or display, and the outlet and fuse are good, it usually needs replacing or repair by someone experienced.
Safety first
- Unplug the supply before you open it or move its leads.
- Do not open sealed wall adapters.
- Bench supplies and PC power supplies keep their mains-side capacitors charged after unplugging. Do not work inside them unless you are trained to.
- When you probe a live unit, keep one hand clear of the equipment, so that a shock cannot pass across your chest.
Start with the simple checks
- Outlet. Test the outlet with a device you know works.
- Cord and plug. Look for damage, a loose connection or a bent pin.
- Power switch. Make sure the unit’s mains switch is on.
- Fuse. Bench supplies have a mains-side fuse. A blown fuse is a symptom. Replace it with one of the same rating and type, and look for the cause.
- Output setting. On a bench unit, check that the output is enabled and that the current limit is not set very low. A low limit can make the output drop to near zero as soon as a load connects.
- Connector. Check that the plug is fully seated and that the polarity is right. A barrel plug can be loose in its socket.
Wall adapters
- Plug the adapter into a working outlet.
- Set a multimeter to DC volts. Measure across the output tip and sleeve, with no load connected.
- Compare the reading with the output rating on the label. It should be close to that figure.
Then:
- Zero output: the adapter has probably failed. Replace it with one that matches the label.
- Correct output, but the device does not work: the fault may be in the cable, the device’s input connector or the device itself. Check those before you blame the adapter.
Keep your probes on the DC output only, and do not touch the mains prongs.
Bench units
- Output enable and mode indicator. If the unit is in constant current (CC) mode, the output voltage falls when the load draws more than the limit. Check the circuit, and raise the limit only after you have confirmed it is safe. The current limit guide explains the settings.
- Protection trips. Many bench supplies shut down on overload or overtemperature. Turn the unit off, remove the load, let it cool, and restart. If it trips again straight away, the fault is in the load or in the supply.
- Fuse. Replace a blown fuse with one of the same rating and type. Replacing it again and again without finding the cause risks a fire.
- Measure the output with the load disconnected, and then with it connected. The difference tells you whether the supply holds its voltage under load.
Signs of an internal fault
Stop and get the unit checked, or replace it, if you notice:
- No lights, fan or display, with a good outlet and an intact fuse.
- A burning smell, scorch marks, or swollen capacitors.
- Clicking, buzzing or a loud whine.
- A fuse that blows as soon as it is fitted.
ATX PC power supplies
A PC power supply with no output is usually checked with the jumper test, which powers it on without a motherboard. The ATX power supply jumper test explains the steps and safety points.
Repair or replace
- Sealed wall adapters: replace them. They are not designed to be opened, and replacement is usually the sensible choice.
- Bench supplies: repair can be worth it for a good-quality unit with a simple fault. Otherwise, replacement is often the better option.
- PC power supplies: replacement is the usual route.
Quick checklist
- The outlet works with another device.
- The cord and plug are undamaged and fully seated.
- The switches are on, and the output is enabled.
- The fuse is intact and of the correct rating.
- The current limit is not set too low.
- The output has been measured with no load, and then with a load.
- There are signs of internal damage? Stop, and replace the unit or get help.
For the basics of how supplies work, see DC power supplies explained. To check a replacement adapter against the original, see how to read a wall adapter label.